SUTE02 Mica Heater
SUTE02 Mica Heater is mainly suitable for plastic injection molding machines, the heating part of the head of blow molding machines, and the heating system of extrusion components, with an operating temperature of up to 350°C.
Detailed Introduction:
SUTE02 Mica Heater Product Introduction
It is mainly suitable for plastic injection molding machines, the heating part of the head of blow molding machines, and the heating system of extrusion components, with an operating temperature of up to 350°C. It has the advantages of small size, small footprint, fast heating, beautiful appearance, and good heat exchange capacity. It is an indispensable heating element in the rubber and plastic industry in China and even internationally, with a maximum surface load of 6.5W/cm².
SUTE02 Mica Heater Specification Table
Model
|
Dimensions (mm) |
Voltage (V) |
Power (W) |
Main Technical Indicators |
LK-YM-Φ55Χ80 |
Φ55Χ80 |
230 |
800 |
1. Operating conditions: ambient temperature -20～+60°C
Relative humidity <80%
2. Leakage current: <0.5mA
3. Insulation resistance: ≥5MΩ
4. Ground resistance: <0.1Ω
5. Withstand voltage: 1500V, no breakdown for 1 minute
6. Temperature resistance: 500°C
7. Power deviation: +5%-10% |
LK-YM-Φ120Χ141 |
Φ120Χ141 |
230 |
2000 |
LK-YM-Φ120Χ51 |
Φ120Χ51 |
230 |
520 |
LK-YM-Φ80Χ60 |
Φ80Χ60 |
230 |
775 |
LK-YM-Φ58Χ43 |
Φ58Χ43 |
230 |
250 |
LK-YM-Φ90Χ51 |
Φ90Χ51 |
230 |
300 |
LK-YM-Φ185Χ51 |
Φ185Χ51 |
230 |
1100 |
LK-YM-Φ130Χ66 |
Φ130Χ66 |
230 |
1000 |
LK-YM-Φ165Χ66 |
Φ165Χ66 |
230 |
1100 |
LK-YM-Φ160Χ70 |
Φ160Χ70 |
220 |
1000 |
LK-YM-Φ230Χ90 |
Φ230Χ90 |
220 |
2200 |
LK-YM-Φ154Χ94 |
Φ154Χ94 |
220 |
1500 |
LK-YM-Φ152Χ100 |
Φ152Χ100 |
220 |
1500 |
LK-YM-Φ180Χ80 |
Φ180Χ80 |
220 |
1300 |
LK-YM-Φ, , , , , , 265Χ75 |
Φ265Χ75 |
220 |
1500 |
LK-YM-Φ90Χ180 |
Φ90Χ180 |
220 |
1700 |
LK-YM-Φ90Χ60 |
Φ90Χ60 |
220 |
550 |
LK-YM-Φ120Χ80 |
Φ120Χ80 |
220 |
1100 |
LK-YM-Φ190Χ135 |
Φ190Χ135 |
220 |
3000 |
LK-YM-Φ185Χ75 |
Φ185Χ75 |
220 |
1500 |
LK-YM-Φ280Χ48 |
Φ280Χ48 |
220 |
1500 |
LK-YM-Φ300Χ100 |
Φ300Χ100 |
220 |
2500 |
LK-YM-Φ320Χ100 |
Φ320Χ100 |
220 |
3000 |
LK-YM-Φ165Χ45 |
Φ165Χ45 |
220 |
800 |
LK-YM-Φ180Χ45 |
Φ180Χ45 |
220 |
900 |
LK-YM-Φ65Χ30 |
Φ65Χ30 |
220 |
200 |
LK-YM-Φ230Χ45 |
Φ230Χ45 |
220 |
1000 |
LK-YM-Φ55Χ100 |
Φ55Χ100 |
230 |
1000 |
LK-YM-Φ80Χ70 |
Φ80Χ70 |
230 |
650 |
LK-YM-Φ70Χ70 |
Φ70Χ70 |
230 |
600 |
LK-YM-Φ85Χ45 |
Φ85Χ45 |
230 |
530 |
LK-YM-Φ110Χ100 |
Φ110Χ100 |
230 |
150 |
LK-YM-Φ102Χ70 |
Φ102Χ70 |
230 |
700 |
Customization is available according to customer requirements, please refer to the ordering guide |
SUTE02 Mica Heater Ordering Guide:
Mica Heater The inner diameter size is very important. Even a small error in diameter can cause trouble during installation, so it is required to provide the following parameters accurately when ordering:
1. Diameter (for mica ring: inner diameter in mm or outer diameter in mm when internal application is required; for square: length in mm)
2. Width (mm)
3. Lead wire type, length, and position
4. Position and size of thermocouple holes or cutouts
5. Voltage and power
6. Single piece or double piece
7. Special gap width
8. If marking on the shell is required, specify the content for laser marking
9. Order quantity
10. Delivery deadline
* It is best to provide mechanical drawings or sketches when ordering
